Skip to the content
Peabody Teach

Share

This page

Peabody is free and has no ads. Sharing it is the best way to help.

Grade 3 scientific practices: Levers, tests and better builds

A reading on levers, fair tests and the design process, a ruler lever test, three practice sheets and a check, with a key.

Grade 3 · 45 minutes · worksheet

Reading: levers and fair tests

Name ______________ Date ____________

A simple machine helps us do work with less effort. A lever is a stiff bar that rests on a point called the fulcrum. The heavy thing you want to move is the load. Push down on one end, and the other end goes up. A seesaw and a wheelbarrow are levers.

Where the fulcrum sits matters. Put it close to the load. Then a small push, far from the fulcrum, can lift it. The farther your push is from the fulcrum, the less force you need. But you push down a longer way.

Scientists use a fair test. In a fair test, you change only one thing. You keep everything else the same. Then you measure the result. Engineers use the design process. They ask about a problem, make a plan, build, test and improve. If the first design fails, that is fine. The test shows how to make it better.

WordMeaning
simple machinea tool that helps do work
levera stiff bar that turns on a point
fulcrumthe point a lever turns on
loadthe thing you want to move
fair testa test that changes one thing
designa plan for how to build something

Hands-on: where should the fulcrum go?

Materials: a 12 inch ruler, a pencil, a paper cup, tape, 6 erasers, and 30 pennies. Test the fulcrum in three places and keep all else the same.

StepWhat to doSafety
1. Set upLay the pencil under the ruler middle.An adult is nearby.
2. LoadStack the erasers on one end.Keep fingers clear of the ends.
3. CupTape the cup to the other end.Use tape, not sharp tools.
4. AddAdd pennies to the cup one at a time.Keep pennies out of your mouth.
5. CountCount pennies when the load lifts.Keep your seat.
6. MoveMove the pencil. Repeat. Wash hands.Wash hands with soap.
Fulcrum placePennies to lift the load
Close to the load_____
In the middle_____
Close to the cup_____

Practice 1: what is it?

Sheet 1: pick the best answer.

  1. What is a lever?a) A kind of wheelb) A flat rampc) A stiff bar that turns on a point
  2. Look at the picture word: fulcrum. What is a fulcrum?a) The point the lever turns onb) The heavy thingc) The push
  3. Look at the picture word: seesaw. A seesaw is a kind of what?a) Rampb) Leverc) Pulley
  4. What is the load?a) The place you pushb) The point it rests onc) The thing you want to move
  5. In a fair test, how many things do you change?a) Oneb) Twoc) All of them
  6. What does a simple machine help us do?a) Make noiseb) Do work with less effortc) Make heat

Practice 2: use what you know

Sheet 2: pick the best answer.

  1. A heavy child and a light child want to balance a seesaw. Where should the heavy child sit?a) Farther from the middleb) Closer to the middlec) On the ground
  2. You move the fulcrum closer to the load. What happens to the push you need?a) You need less pushb) You need more pushc) Nothing changes
  3. A class tests how far a toy car rolls down a ramp. They change only the ramp height. What must stay the same?a) The ramp heightb) Nothingc) The car and the floor
  4. A lever is too weak to lift the load. What should the team do next?a) Change the design and test againb) Give upc) Say that it works
  5. Which test is fair?a) A new plane and a new throwb) The same plane and the same throw, but a new wing foldc) A new plane, a new throw and a new room
  6. A student lifts a box with a plank on a block. Which part is the fulcrum?a) The boxb) The student's handc) The block

Practice 3: explain and compare

Sheet 3: pick the best answer.

  1. Why does a long lever make lifting easier?a) Pushing far from the fulcrum needs less forceb) Long levers weigh lessc) Long levers have no load
  2. What do you give up for the easier push?a) You push harderb) You push down a longer wayc) You lift less
  3. Why change only one thing in a test?a) It is fasterb) It looks neatc) You know what caused the result
  4. How are a seesaw and a wheelbarrow alike?a) Both are leversb) Both are rampsc) Neither has a load
  5. Why do engineers test and improve a design?a) The first try may not work wellb) Tests make it look oldc) A design never needs a test
  6. Which is the right order?a) Test, plan, improve, buildb) Plan, build, test, improvec) Improve, build, plan, test

Check: show what you learned

Check: answer each one.

  1. A lever turns on a fulcrum.TrueFalse
  2. In a fair test you change many things.TrueFalse
  3. What do you measure in a fair test?a) The resultb) The fulcrumc) The weather
  4. The load is the thing you want to move.TrueFalse
  5. Which one is a lever?a) A cloudb) A seesawc) A rock
  6. What is the first step of the design process?a) Test itb) Improve itc) Ask about a problem

Write: tell how you could lift a heavy book with a ruler and a pencil.

Made with Peabody Teach, free printables for teachers: teach.peabody.kids. No sign-in, no ads.

Teacher copy with the answer key

Leer esta página en español

Last checked 2026-11-15. Every answer in it was worked out a second time without the key. Something wrong? Tell us.